How to cut laminate countertop for sink

A table saw, circular saw, or reciprocating saw should be able to cut the counters. With regards to the different saws, you need to take some precautions. A jig saw with work for this. I would add the laminate first.

It would also help to tape around the arear you are about to cut with painters tape. This will help make a cleaner cut. It is not a hard job for a person that has done it before.

When cut , laminate tends to chip or splinter but you can. How to Cut a Hole in Countertop for a Sink. Leah from See Jane Drill demonstrates a simulation of how to cut a hole in counter top to install a sink.

To cut a hole for a sink , it’s easiest to use a jigsaw, which allows for great control. Always, always, always use a new jigsaw blade. An old or dull blade can chip the laminate along the cutting line. Drill two starter holes in opposite corners just inside the cutting line. Because laminate countertop is a relatively soft material, a normal circular saw blade for cutting wood is capable of cutting through it with ease.

According to WoodworkingTips. In this video, senior editor and old-school carpenter Andy Engel takes on cutting a sink opening in a laminate countertop. You’ll get tips on layout, cutting without chipping, and how to make cuts in hard-to-reach corners. This step by step diy article is about how to cut a hole in laminate countertop.

If you are remodeling your kitchen, you should probably know that cutting out holes in laminate countertops is require if you are fitting a sink or a gas stove. A few important things to keep in mind when cutting out a coutretop for a basin or sink. These few tips will make your job go much easier. Formica is a versatile, plastic laminate that comes in a wide range of colors, textures, and finishes.

Cutting a Laminate Countertop - DIY - Duration: 5:41. Using Formica allows a homeowner to customize an area with a laminate that is durable and easy to clean. Any time I have had to cut a laminate top for a sink it has been in the field. The only sink I have ever seen go into a laminate top is a surface mount sink with an edge that lips over the lam and covers the edge of the cut -out. Installing laminate counters (Kitchen makeover).

If you need to make a cut -out for the sink and range top, use the old laminate countertop as a guide. If you’re installing a new sink or range top, use the template that comes in the box. If your sink or range top did not come with a template, set the item upside down on top of the new countertop. Center it and trace the outline. You can cut accurately to a pencil line without having to grind or sand.

If the countertop is a postform top and the cutout is close to the backsplash, I reach under and cut the corners out from below. Trace around the sink template and cut the sink hole in the counter using a jigsaw. Use a paint roller to apply contact cement to the top of the counter and to the back side of the countertop laminate. If your countertop is precut for the sink , you will not need to do most of these steps.

New sinks will come with a template for you to use to cut your opening. Or you can use the sink itself to make the opening you want. To compare costs of countertop materials, like laminate and granite, you will need to provide contractors with the approximate square footage of. Now it’s time to glue down the laminate. I explained all about the process of installing DIY laminate countertops HERE.

With a Karran sink , you just lay the laminate sheet right over the top of the whole sink , then cut it out later. L-shaped kitchen countertop with a cutout for a sink or rangetop installation:. Install a laminate countertop to refresh your kitchen or bath’s appearance. You can build a laminate countertop from scratch or purchase a pre-manufactured countertop , which is called a post-form countertop. Post-form countertops are made in standard-sized lengths and come pre-assembled complete with backsplash.

The counter is cut to accommodate the sink and the sink set inside with the rim flush to the laminate. Adhesive is injected between the sides of the sink and counter. Then the laminate is cut away, routed and sanded for a consistent transition. Mark the center of the sink cabinet on the countertop.

For the Pedraza kitchen, it required an foot countertop and a foot countertop. So the total cost for the butcher block itself was $7which is a decent chunk of change but for the end result…. Once the countertops were cut and dry fit to the cabinets and walls….

The weight of the sink is supported by the countertop.